Occasionally while debugging, selecting “Reset program” closes both, the 
program and the workbench.
The program should terminate, but the workbench shall remain open and 
running.
-Itai

Hi Itai,

Is there something you can show us? Of course terminating the debuggee
shall not terminate the debugger....

  Andreas Herdt
  Alaska Software

--------------------------------------------------------------------

Technical Support:      support@alaska-software.com

News Server:            news.alaska-software.com
Homepage:               http://www.alaska-software.com
WebKnowledgeBase:       http://www.alaska-software.com/kbase.shtm

Fax European Office:    +49 (0) 61 96 - 77 99 99 23
Fax US Office:          +1 (646) 218 1281
--------------------------------------------------------------------

"Itai Ben-Artzi" wrote in message 
news:7c56715d$cddc150$6fe96@news.alaska-software.com...
> Occasionally while debugging, selecting “Reset program” closes both, the 
> program and the workbench.
> The program should terminate, but the workbench shall remain open and 
> running.
> -Itai

Andreas,
It does not happen consistently, but occurred 4-5 times.  I’ll try to 
reproduce it on the next time it happened.
-Itai

Hi Itai,

Investigating in this case, please be to some kind sensitive to the
Debugger found in the "Tools -> Debugger Options..." dialog.

What are your settings in "Show Debugger Hints", "Evaluate
Expressions" and "Inspect ACCESS/ASSIGN".

Those settings have a big impact on the overall behaviour of the
debugger and therefore can be the source of potential problems.

By the way, do you still observe those uncracefull shutdowns?

With my best regards,

  Andreas Herdt
  Alaska Software

--------------------------------------------------------------------

Technical Support:      support@alaska-software.com

News Server:            news.alaska-software.com
Homepage:               http://www.alaska-software.com
WebKnowledgeBase:       http://www.alaska-software.com/kbase.shtm

Fax European Office:    +49 (0) 61 96 - 77 99 99 23
Fax US Office:          +1 (646) 218 1281
--------------------------------------------------------------------

"Itai Ben-Artzi" wrote in message 
news:763dd09d$32834d6$12bad@news.alaska-software.com...
> Andreas,
> It does not happen consistently, but occurred 4-5 times.  I’ll try to 
> reproduce it on the next time it happened.
> -Itai
>

Andreas,
I’ve had again two similar incidents, but trying to reproduce them was not 
successful.  It seems this issue depends on more than just resetting the 
application at specific point.  Below are the settings of the requested 
options:
Show Debugger Hints is checked; Evaluate Expression is unchecked; Inspect 
ACCESS/ASSIGN is checked.
I hope this help.
-Itai

Hi Itai,

If you have implemented ACESS ASSIGN methods, does it help
to uncheck the corresponding checkmark in the Debugger Options
dialog?

  Andreas Herdt
  Alaska Software

--------------------------------------------------------------------

Technical Support:      support@alaska-software.com

News Server:            news.alaska-software.com
Homepage:               http://www.alaska-software.com
WebKnowledgeBase:       http://www.alaska-software.com/kbase.shtm

Fax European Office:    +49 (0) 61 96 - 77 99 99 23
Fax US Office:          +1 (646) 218 1281
--------------------------------------------------------------------

"Itai Ben-Artzi" wrote in message 
news:391980f6$85c6028$8ebfb@news.alaska-software.com...
> Andreas,
> I’ve had again two similar incidents, but trying to reproduce them was not 
> successful.  It seems this issue depends on more than just resetting the 
> application at specific point.  Below are the settings of the requested 
> options:
> Show Debugger Hints is checked; Evaluate Expression is unchecked; Inspect 
> ACCESS/ASSIGN is checked.
> I hope this help.
> -Itai

Andreas,
Thank you for the follow-up.
I'll check and let you know.
-Itai